The optimizer_switch system variable enables control over optimizer behavior. Its value is a set of flags, each of which has a value of on or off to indicate whether the corresponding optimizer behavior is enabled or disabled. This variable has global and session values and can be changed at runtime. The global default can be set at server startup.

To see the current set of optimizer flags, select the variable value:

mysql> SELECT @@optimizer_switch\G*************************** 1. row ***************************@@optimizer_switch: index_merge=on,index_merge_union=on,                    index_merge_sort_union=on,                    index_merge_intersection=on,                    engine_condition_pushdown=on,                    index_condition_pushdown=on,                    mrr=on,mrr_cost_based=on,                    block_nested_loop=on,batched_key_access=off,                    materialization=on,semijoin=on,loosescan=on,                    firstmatch=on,                    subquery_materialization_cost_based=on,                    use_index_extensions=on

To change the value of optimizer_switch, assign a value consisting of a comma-separated list of one or more commands:

SET [GLOBAL|SESSION] optimizer_switch='command[,command]...';

Each command value should have one of the forms shown in the following table.

The order of the commands in the value does not matter, although the default command is executed first if present. Setting an opt_name flag to default sets it to whichever of on or off is its default value. Specifying any given opt_name more than once in the value is not permitted and causes an error. Any errors in the value cause the assignment to fail with an error, leaving the value of optimizer_switch unchanged.

The following table lists the permissible opt_name flag names, grouped by optimization strategy.

For batched_key_access to have any effect when set to on, the mrr flag must also be on. Currently, the cost estimation for MRR is too pessimistic. Hence, it is also necessary for mrr_cost_based to be off for BKA to be used.

The semijoin, firstmatch, loosescan, and materialization flags enable control over semi-join and subquery materialization strategies. The semijoin flag controls whether semi-joins are used. If it is set to on, the firstmatch and loosescan flags enable finer control over the permitted semi-join strategies. The materialization flag controls whether subquery materialization is used. If semijoin and materialization are both on, semi-joins also use materialization where applicable. These flags are on by default.

The subquery_materialization_cost_based enables control over the choice between subquery materialization and IN -> EXISTS subquery transformation. If the flag is on (the default), the optimizer performs a cost-based choice between subquery materialization and IN -> EXISTS subquery transformation if either method could be used. If the flag is off, the optimizer chooses subquery materialization over IN -> EXISTS subquery transformation.

For more information about individual optimization strategies, see the following sections:

When you assign a value to optimizer_switch, flags that are not mentioned keep their current values. This makes it possible to enable or disable specific optimizer behaviors in a single statement without affecting other behaviors. The statement does not depend on what other optimizer flags exist and what their values are. Suppose that all Index Merge optimizations are enabled:

mysql> SELECT @@optimizer_switch\G*************************** 1. row ***************************@@optimizer_switch: index_merge=on,index_merge_union=on,                    index_merge_sort_union=on,                    index_merge_intersection=on,                    engine_condition_pushdown=on,                    index_condition_pushdown=on,                    mrr=on,mrr_cost_based=on,                    block_nested_loop=on,batched_key_access=off,                    materialization=on,semijoin=on,loosescan=on,                    firstmatch=on,                    subquery_materialization_cost_based=on,                    use_index_extensions=on

If the server is using the Index Merge Union or Index Merge Sort-Union access methods for certain queries and you want to check whether the optimizer will perform better without them, set the variable value like this:

mysql> SET
        optimizer_switch='index_merge_union=off,index_merge_sort_union=off';mysql> SELECT @@optimizer_switch\G*************************** 1. row ***************************@@optimizer_switch: index_merge=on,index_merge_union=off,                    index_merge_sort_union=off,                    index_merge_intersection=on,                    engine_condition_pushdown=on,                    index_condition_pushdown=on,                    mrr=on,mrr_cost_based=on,                    block_nested_loop=on,batched_key_access=off,                    materialization=on,semijoin=on,loosescan=on,                    firstmatch=on,                    subquery_materialization_cost_based=on,                    use_index_extensions=on