cisco.ios.ios_ospf_interfaces – Модуль ресурса OSPF_Interfaces

• Обзор
• Параметры
• Примечания
• Примеры
• Возвращаемые значения

Обзор

• Этот модуль настраивает и управляет протоколом Open Shortest Path First (OSPF) версии 2 на платформах IOS.

Параметры

Примечания

Примеры

# Using deleted

# Before state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ipv6 ospf 55 area 105
#  ipv6 ospf priority 20
#  ipv6 ospf transmit-delay 30
#  ipv6 ospf adjacency stagger disable
# interface GigabitEthernet0/2
#  ip ospf priority 40
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf 10 area 20
#  ip ospf cost 30

- name: Delete provided OSPF Interface config
  cisco.ios.ios_ospf_interfaces:
    config:
      - name: GigabitEthernet0/1
    state: deleted

#  Commands Fired:
#  ---------------
#
#  "commands": [
#         "interface GigabitEthernet0/1",
#         "no ipv6 ospf 55 area 105",
#         "no ipv6 ospf adjacency stagger disable",
#         "no ipv6 ospf priority 20",
#         "no ipv6 ospf transmit-delay 30"
#     ]

# After state:
# -------------
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
# interface GigabitEthernet0/2
#  ip ospf priority 40
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf 10 area 20
#  ip ospf cost 30

# Using deleted without any config passed (NOTE: This will delete all OSPF Interfaces configuration from device)

# Before state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ipv6 ospf 55 area 105
#  ipv6 ospf priority 20
#  ipv6 ospf transmit-delay 30
#  ipv6 ospf adjacency stagger disable
# interface GigabitEthernet0/2
#  ip ospf priority 40
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf 10 area 20
#  ip ospf cost 30

- name: Delete all OSPF config from interfaces
  cisco.ios.ios_ospf_interfaces:
    state: deleted

# Commands Fired:
# ---------------
#
#  "commands": [
#         "interface GigabitEthernet0/2",
#         "no ip ospf 10 area 20",
#         "no ip ospf adjacency stagger disable",
#         "no ip ospf cost 30",
#         "no ip ospf priority 40",
#         "no ip ospf ttl-security hops 50",
#         "interface GigabitEthernet0/1",
#         "no ipv6 ospf 55 area 105",
#         "no ipv6 ospf adjacency stagger disable",
#         "no ipv6 ospf priority 20",
#         "no ipv6 ospf transmit-delay 30"
#     ]

# After state:
# -------------
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
# interface GigabitEthernet0/2

# Using merged

# Before state:
# -------------
#
# router-ios#sh running-config | section ^interface
# router-ios#

- name: Merge provided OSPF Interfaces configuration
  cisco.ios.ios_ospf_interfaces:
    config:
      - name: GigabitEthernet0/1
        address_family:
          - afi: ipv4
            process:
              id: 10
              area_id: 30
            adjacency: true
            bfd: true
            cost:
              interface_cost: 5
            dead_interval:
              time: 5
            demand_circuit:
              ignore: true
            network:
              broadcast: true
            priority: 25
            resync_timeout: 10
            shutdown: true
            ttl_security:
              hops: 50
          - afi: ipv6
            process:
              id: 35
              area_id: 45
            adjacency: true
            database_filter: true
            manet:
              link_metrics:
                cost_threshold: 10
            priority: 55
            transmit_delay: 45
    state: merged

#  Commands Fired:
#  ---------------
#
#   "commands": [
#         "interface GigabitEthernet0/1",
#         "ip ospf 10 area 30",
#         "ip ospf adjacency stagger disable",
#         "ip ospf bfd",
#         "ip ospf cost 5",
#         "ip ospf dead-interval 5",
#         "ip ospf demand-circuit ignore",
#         "ip ospf network broadcast",
#         "ip ospf priority 25",
#         "ip ospf resync-timeout 10",
#         "ip ospf shutdown",
#         "ip ospf ttl-security hops 50",
#         "ipv6 ospf 35 area 45",
#         "ipv6 ospf adjacency stagger disable",
#         "ipv6 ospf database-filter all out",
#         "ipv6 ospf manet peering link-metrics 10",
#         "ipv6 ospf priority 55",
#         "ipv6 ospf transmit-delay 45"
#     ]

# After state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/2

# Using overridden

# Before state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/2

- name: Override provided OSPF Interfaces configuration
  cisco.ios.ios_ospf_interfaces:
    config:
      - name: GigabitEthernet0/1
        address_family:
          - afi: ipv6
            process:
              id: 55
              area_id: 105
            adjacency: true
            priority: 20
            transmit_delay: 30
      - name: GigabitEthernet0/2
        address_family:
          - afi: ipv4
            process:
              id: 10
              area_id: 20
            adjacency: true
            cost:
              interface_cost: 30
            priority: 40
            ttl_security:
              hops: 50
    state: overridden

# Commands Fired:
# ---------------
#
#  "commands": [
#         "interface GigabitEthernet0/2",
#         "ip ospf 10 area 20",
#         "ip ospf adjacency stagger disable",
#         "ip ospf cost 30",
#         "ip ospf priority 40",
#         "ip ospf ttl-security hops 50",
#         "interface GigabitEthernet0/1",
#         "ipv6 ospf 55 area 105",
#         "no ipv6 ospf database-filter all out",
#         "no ipv6 ospf manet peering link-metrics 10",
#         "ipv6 ospf priority 20",
#         "ipv6 ospf transmit-delay 30",
#         "no ip ospf 10 area 30",
#         "no ip ospf adjacency stagger disable",
#         "no ip ospf bfd",
#         "no ip ospf cost 5",
#         "no ip ospf dead-interval 5",
#         "no ip ospf demand-circuit ignore",
#         "no ip ospf network broadcast",
#         "no ip ospf priority 25",
#         "no ip ospf resync-timeout 10",
#         "no ip ospf shutdown",
#         "no ip ospf ttl-security hops 50"
#     ]

# After state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ipv6 ospf 55 area 105
#  ipv6 ospf priority 20
#  ipv6 ospf transmit-delay 30
#  ipv6 ospf adjacency stagger disable
# interface GigabitEthernet0/2
#  ip ospf priority 40
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf 10 area 20
#  ip ospf cost 30

# Using replaced

# Before state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/2

- name: Replaced provided OSPF Interfaces configuration
  cisco.ios.ios_ospf_interfaces:
    config:
      - name: GigabitEthernet0/2
        address_family:
          - afi: ipv6
            process:
              id: 55
              area_id: 105
            adjacency: true
            priority: 20
            transmit_delay: 30
    state: replaced

# Commands Fired:
# ---------------
#  "commands": [
#         "interface GigabitEthernet0/2",
#         "ipv6 ospf 55 area 105",
#         "ipv6 ospf adjacency stagger disable",
#         "ipv6 ospf priority 20",
#         "ipv6 ospf transmit-delay 30"
#     ]

# After state:
# -------------
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/2
#  ipv6 ospf 55 area 105
#  ipv6 ospf priority 20
#  ipv6 ospf transmit-delay 30
#  ipv6 ospf adjacency stagger disable

# Using Gathered

# Before state:
# -------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/2

- name: Gather OSPF Interfaces provided configurations
  cisco.ios.ios_ospf_interfaces:
    config:
    state: gathered

# Module Execution Result:
# ------------------------
#
#  "gathered": [
#         {
#             "name": "GigabitEthernet0/2"
#         },
#         {
#             "address_family": [
#                 {
#                     "adjacency": true,
#                     "afi": "ipv4",
#                     "bfd": true,
#                     "cost": {
#                         "interface_cost": 5
#                     },
#                     "dead_interval": {
#                         "time": 5
#                     },
#                     "demand_circuit": {
#                         "ignore": true
#                     },
#                     "network": {
#                         "broadcast": true
#                     },
#                     "priority": 25,
#                     "process": {
#                         "area_id": "30",
#                         "id": 10
#                     },
#                     "resync_timeout": 10,
#                     "shutdown": true,
#                     "ttl_security": {
#                         "hops": 50
#                     }
#                 },
#                 {
#                     "adjacency": true,
#                     "afi": "ipv6",
#                     "database_filter": true,
#                     "manet": {
#                         "link_metrics": {
#                             "cost_threshold": 10
#                         }
#                     },
#                     "priority": 55,
#                     "process": {
#                         "area_id": "45",
#                         "id": 35
#                     },
#                     "transmit_delay": 45
#                 }
#             ],
#             "name": "GigabitEthernet0/1"
#         },
#         {
#             "name": "GigabitEthernet0/0"
#         }
#  ]

# After state:
# ------------
#
# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/0
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/2

# Using Rendered

- name: Render the commands for provided  configuration
  cisco.ios.ios_ospf_interfaces:
    config:
      - name: GigabitEthernet0/1
        address_family:
          - afi: ipv4
            process:
              id: 10
              area_id: 30
            adjacency: true
            bfd: true
            cost:
              interface_cost: 5
            dead_interval:
              time: 5
            demand_circuit:
              ignore: true
            network:
              broadcast: true
            priority: 25
            resync_timeout: 10
            shutdown: true
            ttl_security:
              hops: 50
          - afi: ipv6
            process:
              id: 35
              area_id: 45
            adjacency: true
            database_filter: true
            manet:
              link_metrics:
                cost_threshold: 10
            priority: 55
            transmit_delay: 45
    state: rendered

# Module Execution Result:
# ------------------------
#
#  "rendered": [
#         "interface GigabitEthernet0/1",
#         "ip ospf 10 area 30",
#         "ip ospf adjacency stagger disable",
#         "ip ospf bfd",
#         "ip ospf cost 5",
#         "ip ospf dead-interval 5",
#         "ip ospf demand-circuit ignore",
#         "ip ospf network broadcast",
#         "ip ospf priority 25",
#         "ip ospf resync-timeout 10",
#         "ip ospf shutdown",
#         "ip ospf ttl-security hops 50",
#         "ipv6 ospf 35 area 45",
#         "ipv6 ospf adjacency stagger disable",
#         "ipv6 ospf database-filter all out",
#         "ipv6 ospf manet peering link-metrics 10",
#         "ipv6 ospf priority 55",
#         "ipv6 ospf transmit-delay 45"
#     ]

# Using Parsed

# File: parsed.cfg
# ----------------
#
# interface GigabitEthernet0/2
# interface GigabitEthernet0/1
#  ip ospf network broadcast
#  ip ospf resync-timeout 10
#  ip ospf dead-interval 5
#  ip ospf priority 25
#  ip ospf demand-circuit ignore
#  ip ospf bfd
#  ip ospf adjacency stagger disable
#  ip ospf ttl-security hops 50
#  ip ospf shutdown
#  ip ospf 10 area 30
#  ip ospf cost 5
#  ipv6 ospf 35 area 45
#  ipv6 ospf priority 55
#  ipv6 ospf transmit-delay 45
#  ipv6 ospf database-filter all out
#  ipv6 ospf adjacency stagger disable
#  ipv6 ospf manet peering link-metrics 10
# interface GigabitEthernet0/0

- name: Parse the provided configuration with the exisiting running configuration
  cisco.ios.ios_ospf_interfaces:
    running_config: "{{ lookup('file', 'parsed.cfg') }}"
    state: parsed

# Module Execution Result:
# ------------------------
#
#  "parsed": [
#         },
#         {
#             "name": "GigabitEthernet0/2"
#         },
#         {
#             "address_family": [
#                 {
#                     "adjacency": true,
#                     "afi": "ipv4",
#                     "bfd": true,
#                     "cost": {
#                         "interface_cost": 5
#                     },
#                     "dead_interval": {
#                         "time": 5
#                     },
#                     "demand_circuit": {
#                         "ignore": true
#                     },
#                     "network": {
#                         "broadcast": true
#                     },
#                     "priority": 25,
#                     "process": {
#                         "area_id": "30",
#                         "id": 10
#                     },
#                     "resync_timeout": 10,
#                     "shutdown": true,
#                     "ttl_security": {
#                         "hops": 50
#                     }
#                 },
#                 {
#                     "adjacency": true,
#                     "afi": "ipv6",
#                     "database_filter": true,
#                     "manet": {
#                         "link_metrics": {
#                             "cost_threshold": 10
#                         }
#                     },
#                     "priority": 55,
#                     "process": {
#                         "area_id": "45",
#                         "id": 35
#                     },
#                     "transmit_delay": 45
#                 }
#             ],
#             "name": "GigabitEthernet0/1"
#         },
#         {
#             "name": "GigabitEthernet0/0"
#         }
#     ]

Значения возврата

Общие значения возврата описаны здесь, следующие являются полями, уникальными для данного модуля:

Авторы

• Sumit Jaiswal (@justjais)