vyos_interfaces – Управляет атрибутами интерфейсов устройств сети VyOS

Новое в версии 2.9.

Описание
Параметры
Примечания
Примеры
Возвращаемые значения
Статус

Описание

Этот модуль управляет атрибутами интерфейсов на устройствах сети VyOS.
Этот модуль поддерживает управление базовыми атрибутами интерфейсов Ethernet, Bonding, VXLAN, Loopback и Virtual Tunnel.

Параметры

Параметр			Варианты/Значения по умолчанию	Комментарии
config список				Настройка предоставленных интерфейсов.
	description строка			Описание интерфейса.
	duplex строка		Варианты: full half auto	Режим дуплексирования интерфейса. Применимо только для интерфейсов Ethernet.
	enabled логическое значение		Варианты: no yes ←	Административное состояние интерфейса. Установите значение в `true` для административного включения интерфейса или `false` для его отключения.
	mtu целое число			MTU для конкретного интерфейса. Обратитесь к документации поставщика для допустимых значений. Применимо для интерфейсов Ethernet, Bonding, VXLAN и Virtual Tunnel.
	name строка / обязательно			Полное имя интерфейса, например, eth0, eth1, bond0, vti1, vxlan2.
	speed строка		Варианты: auto 10 100 1000 2500 10000	Скорость соединения интерфейса. Применимо только для интерфейсов Ethernet.
	vifs список			Настройка виртуальных под-интерфейсов. Интерфейсы VLAN 802.1Q представлены в VyOS как виртуальные под-интерфейсы.
		description строка		Описание виртуального под-интерфейса.
		enabled логическое значение	Варианты: no yes ←	Административное состояние виртуального под-интерфейса. Установите значение в `true` для административного включения интерфейса или `false` для его отключения.
		mtu целое число		MTU для виртуального под-интерфейса. Обратитесь к документации поставщика для допустимых значений.
		vlan_id целое число		Идентификатор виртуального под-интерфейса.
state строка			Варианты: merged ← replaced overridden deleted	Состояние конфигурации после завершения модуля.

Примечания

Примечание

Проверено на VyOS 1.1.8 (helium).
Этот модуль работает с подключением network_cli. См. параметры платформы VyOS.

Примеры

# Using merged
#
# -------------
# Before state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo

- name: Merge provided configuration with device configuration
  vyos_interfaces:
    config:
      - name: eth2
        description: 'Configured by Ansible'
        enabled: True
        vifs:
          - vlan_id: 200
            description: "VIF 200 - ETH2"

      - name: eth3
        description: 'Configured by Ansible'
        mtu: 1500

      - name: bond1
        description: 'Bond - 1'
        mtu: 1200

      - name: vti2
        description: 'VTI - 2'
        enabled: false
    state: merged
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
# "before": [
#           {
#            "enabled": true,
#            "name": "lo"
#           },
#       {
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "enabled": true,
#            "name": "eth2"
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "set interfaces ethernet eth2 description 'Configured by Ansible'",
#        "set interfaces ethernet eth2 vif 200",
#        "set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'",
#        "set interfaces ethernet eth3 description 'Configured by Ansible'",
#        "set interfaces ethernet eth3 mtu '1500'",
#        "set interfaces bonding bond1",
#        "set interfaces bonding bond1 description 'Bond - 1'",
#        "set interfaces bonding bond1 mtu '1200'",
#        "set interfaces vti vti2",
#        "set interfaces vti vti2 description 'VTI - 2'",
#        "set interfaces vti vti2 disable"
#    ]
#
# "after": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1200,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "VTI - 2",
#            "enabled": false,
#            "name": "vti2"
#        },
#        {
#            "description": "Configured by Ansible",
#            "enabled": true,
#            "mtu": 1500,
#            "name": "eth3"
#        },
#        {
#            "description": "Configured by Ansible",
#            "enabled": true,
#            "name": "eth2",
#            "vifs": [
#                {
#                    "description": "VIF 200 - ETH2",
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# -------------
# After state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1200'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces loopback lo
# set interfaces vti vti2 description 'VTI - 2'
# set interfaces vti vti2 disable
#


# Using replaced
#
# -------------
# Before state:
# -------------
#
# vyos:~$ show configuration commands | grep eth
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:f3:6c:b5'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ad:ef:65'
# set interfaces ethernet eth1 smp_affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:ab:4e:79'
# set interfaces ethernet eth2 mtu '500'
# set interfaces ethernet eth2 smp_affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth2 vif 200 description 'Configured by Ansible'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:17:3c:85'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces ethernet eth3 smp_affinity 'auto'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo
#
#
- name: Replace device configurations of listed interfaces with provided configurations
  vyos_interfaces:
    config:
      - name: eth2
        description: "Replaced by Ansible"

      - name: eth3
        description: "Replaced by Ansible"

      - name: eth1
        description: "Replaced by Ansible"
    state: replaced
#
#
# -----------------------
# Module Execution Result
# -----------------------
#
# "before": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1400,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": true,
#            "mtu": 1500,
#            "name": "eth3",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": true,
#            "mtu": 500,
#            "name": "eth2",
#            "speed": "100",
#            "vifs": [
#                {
#                    "description": "VIF 200 - ETH2",
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "description": "Configured by Ansible Eng Team",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth1",
#            "speed": "100"
#        },
#        {
#            "description": "Management Interface for the Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces ethernet eth2 speed",
#        "delete interfaces ethernet eth2 duplex",
#        "delete interfaces ethernet eth2 mtu",
#        "delete interfaces ethernet eth2 vif 200 description",
#        "set interfaces ethernet eth2 description 'Replaced by Ansible'",
#        "delete interfaces ethernet eth3 speed",
#        "delete interfaces ethernet eth3 duplex",
#        "delete interfaces ethernet eth3 mtu",
#        "set interfaces ethernet eth3 description 'Replaced by Ansible'",
#        "delete interfaces ethernet eth1 speed",
#        "delete interfaces ethernet eth1 duplex",
#        "set interfaces ethernet eth1 description 'Replaced by Ansible'"
#    ]
#
# "after": [
#        {
#            "description": "Bond - 1",
#            "enabled": true,
#            "mtu": 1400,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth2",
#            "vifs": [
#                {
#                    "enabled": true,
#                    "vlan_id": "200"
#                }
#            ]
#        },
#        {
#            "description": "Replaced by Ansible",
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "description": "Management Interface for the Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# -------------
# After state:
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Replaced by Ansible'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Replaced by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200
# set interfaces ethernet eth3 description 'Replaced by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
#
#
# Using overridden
#
#
# --------------
# Before state
# --------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Ethernet Interface - 0'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 mtu '1200'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 mtu '100'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100 description 'VIF 100 - ETH1'
# set interfaces ethernet eth1 vif 100 disable
# set interfaces ethernet eth2 description 'Configured by Ansible Team (Admin Down)'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
# set interfaces vti vti1 description 'Virtual Tunnel Interface - 1'
# set interfaces vti vti1 mtu '68'
#
#
- name: Overrides all device configuration with provided configuration
  vyos_interfaces:
    config:
      - name: eth0
        description: Outbound Interface For The Appliance
        speed: auto
        duplex: auto

      - name: eth2
        speed: auto
        duplex: auto

      - name: eth3
        mtu: 1200
    state: overridden
#
#
# ------------------------
# Module Execution Result
# ------------------------
#
# "before": [
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Virtual Tunnel Interface - 1",
#            "enabled": true,
#            "mtu": 68,
#            "name": "vti1"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "description": "Configured by Ansible Team (Admin Down)",
#            "enabled": false,
#            "mtu": 600,
#            "name": "eth2"
#        },
#        {
#            "description": "Configured by Ansible Eng Team",
#            "enabled": true,
#            "mtu": 100,
#            "name": "eth1",
#            "vifs": [
#                {
#                    "description": "VIF 100 - ETH1",
#                    "enabled": false,
#                    "vlan_id": "100"
#                }
#            ]
#        },
#        {
#            "description": "Ethernet Interface - 0",
#            "duplex": "auto",
#            "enabled": true,
#            "mtu": 1200,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces vti vti1 description",
#        "delete interfaces vti vti1 mtu",
#        "delete interfaces ethernet eth1 description",
#        "delete interfaces ethernet eth1 mtu",
#        "delete interfaces ethernet eth1 vif 100 description",
#        "delete interfaces ethernet eth1 vif 100 disable",
#        "delete interfaces ethernet eth0 mtu",
#        "set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'",
#        "delete interfaces ethernet eth2 description",
#        "delete interfaces ethernet eth2 mtu",
#        "set interfaces ethernet eth2 duplex 'auto'",
#        "delete interfaces ethernet eth2 disable",
#        "set interfaces ethernet eth2 speed 'auto'",
#        "delete interfaces ethernet eth3 description",
#        "set interfaces ethernet eth3 mtu '1200'"
#    ],
#
# "after": [
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "enabled": true,
#            "name": "vti1"
#        },
#        {
#            "enabled": true,
#            "mtu": 1200,
#            "name": "eth3"
#        },
#        {
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth2",
#            "speed": "auto"
#        },
#        {
#            "enabled": true,
#            "name": "eth1",
#            "vifs": [
#                {
#                    "enabled": true,
#                    "vlan_id": "100"
#                }
#            ]
#        },
#        {
#            "description": "Outbound Interface For The Appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# ------------
# After state
# ------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100
# set interfaces ethernet eth2 duplex 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1200'
# set interfaces loopback lo
# set interfaces vti vti1
#
#
# Using deleted
#
#
# -------------
# Before state
# -------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1 description 'LAG - 1'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Network'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo
#
#
- name: Delete attributes of given interfaces (Note - This won't delete the interfaces themselves)
  vyos_interfaces:
    config:
      - name: bond1

      - name: eth1

      - name: eth2

      - name: eth3
    state: deleted
#
#
# ------------------------
# Module Execution Results
# ------------------------
#
# "before": [
#        {
#            "enabled": true,
#            "mtu": 1300,
#            "name": "bond0"
#        },
#        {
#            "description": "LAG - 1",
#            "enabled": true,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth3",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible",
#            "duplex": "full",
#            "enabled": false,
#            "mtu": 600,
#            "name": "eth2",
#            "speed": "100"
#        },
#        {
#            "description": "Configured by Ansible Network",
#            "duplex": "full",
#            "enabled": true,
#            "name": "eth1",
#            "speed": "100"
#        },
#        {
#            "description": "Outbound Interface for this appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
# "commands": [
#        "delete interfaces bonding bond1 description",
#        "delete interfaces ethernet eth1 speed",
#        "delete interfaces ethernet eth1 duplex",
#        "delete interfaces ethernet eth1 description",
#        "delete interfaces ethernet eth2 speed",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 duplex",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 description",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth2 mtu",
#        "delete interfaces ethernet eth2 disable",
#        "delete interfaces ethernet eth3 speed",
#        "delete interfaces ethernet eth3 duplex",
#        "delete interfaces ethernet eth3 description"
#    ]
#
# "after": [
#        {
#            "enabled": true,
#            "mtu": 1300,
#            "name": "bond0"
#        },
#        {
#            "enabled": true,
#            "name": "bond1"
#        },
#        {
#            "enabled": true,
#            "name": "lo"
#        },
#        {
#            "enabled": true,
#            "name": "eth3"
#        },
#        {
#            "enabled": true,
#            "name": "eth2"
#        },
#        {
#            "enabled": true,
#            "name": "eth1"
#        },
#        {
#            "description": "Outbound Interface for this appliance",
#            "duplex": "auto",
#            "enabled": true,
#            "name": "eth0",
#            "speed": "auto"
#        }
#    ]
#
#
# ------------
# After state
# ------------
#
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
#
#

Возвращаемые значения

Общие возвращаемые значения описаны здесь, следующие — поля, уникальные для этого модуля:

Ключ	Возвращаемое значение	Описание
after список	при изменении	Конфигурация как структурированные данные после завершения модуля. Пример: Возвращаемая конфигурация всегда будет в том же формате, что и параметры выше.
before список	всегда	Конфигурация как структурированные данные до вызова модуля. Пример: Возвращаемая конфигурация всегда будет в том же формате, что и параметры выше.
commands список	всегда	Набор команд, отправленных на удалённое устройство. Пример: ['set interfaces ethernet eth1 mtu 1200', 'set interfaces ethernet eth2 vif 100 description VIF 100']

Статус

Данный модуль не гарантирует обратную совместимость интерфейса. [превью]
Этот модуль поддерживается командой Ansible Network Team. [network]

Поддержка Red Hat

Дополнительную информацию о поддержке этого модуля Red Hat можно найти в этой статье базы знаний Red Hat.

Авторы

Nilashish Chakraborty (@nilashishc)

Подсказка

Если вы обнаружите какие-либо проблемы в этой документации, вы можете отредактировать этот документ, чтобы улучшить его.

© 2012–2018 Michael DeHaan
© 2018–2019 Red Hat, Inc.
Licensed under the GNU General Public License version 3.
https://docs.ansible.com/ansible/2.9/modules/vyos_interfaces_module.html